Thank you to all our customers for an amazing year! We wish you a wonderful holiday season. Please note that due to the holidays, service and shipping may be delayed.
P4016 AXEO Performance FLH Touring Install Guide
Fitment: 1997 - 2024 Harley-Davidson FL Touring Models
NOTE: LEGEND SUSPENSIONS RECOMMENDS THE USE OF THE FOLLOWING FORK OILS: SCREAMIN' EAGLE HEAVY, MAXIMA 20W V-TWIN, OR AN EQUIVALENT 20W FORK OIL
ATTENTION: Additional parts are required when installing this kit with a 21" or 23" front wheel. Order one of the following Travel Limiter Kits prior to installation:
| Year and Model | 21" Wheel | 23" Wheel |
|---|---|---|
| 2017-2024 Harley-Davidson FLH Touring Models (49MM) | Part Number: 0414-0760 | Part Number: 0414-0761 |
| 2014-2016 Harley-Davidson FLH Touring Models (49MM) | Part Number: 0414-0758 | Part Number: 0414-0759 |
| 1997-2013 Harley-Davidson FLH Touring Models (41MM) | Part Number: 0414-0756 | Part Number: 0414-0757 |
STEP ONE: FORK REMOVAL
A. Remove the forks from the motorcycle, consult with an experienced technician before removal if needed.
STEP TWO: DISASSEMBLY
WARNING: Be extremely careful when removing the top cap, it is under high spring pressure and may cause injury.
A. Secure the stanchion (upper fork tube) in a fork vise or soft clamp to avoid scratching it.
B. Use an impact wrench to remove the lower Allen bolt to drain the fork oil. FIGURE A
C. Pump the slider (lower fork tube) and stanchion several times to purge as much of the original oil as possible.
D. With the fork still secured in the vise, use an impact wrench to remove the top cap. FIGURE B
E. Dump out all of the stock components from the top of the stanchion. FIGURE C
NOTE: Disassembling the slider and stanchion is unnecessary unless:
- You are installing travel limiters for a 21” or 23” front wheel.
- Your current fork set has an OEM damper cartridge in one leg, you will need to replace the oil lock piece with the one provided by Legend.
- You are replacing your fork seals and bushings
0414-0748: Legend provides one oil lock piece
0414-0747: Customer re-uses OEM oil lock piece
0414-0746: Legend provides one oil piece
WARNING:
DO NOT TAMPER WITH SCHRADER VALVE
STEP THREE: CLEAN FORKS
A. Clean the remaining oil and contaminants from the inside of the fork tubes using a non-corrosive and non-abrasive parts cleaning solvent and a long brush.
B. Rinse thoroughly to remove any residue.
C. Dry parts with compressed air.
STEP FOUR: SET PRELOAD ON LEGEND CARTRIDGES
A. Refer to the preload setting chart below.
(preload measurement is based on rider weight only).
B. Use an Allen wrench to loosen the set screw on the preload adjuster.
FIGURE D
C. Thread the preload adjuster up or down the shaft to achieve the recommended inside measurement between the rebound spring perch and the preload adjuster.
WARNING: Once the proper preload measurement is achieved, index preload adjuster so the set screw lines up with the machined flat on the shaft. Apply blue threadlocker to the set screw threads and tighten.
PRELOAD MEASUREMENT
TAKEN BETWEEN REBOUND SPRING PERCH AND PRELOAD ADJUSTER - AS SHOWN BELOW
*DO NOT EXCEED MAXIMUM MEASUREMENT TO PREVENT DAMAGING CARTRIDGES*
PRELOAD SETTING CHART
RIDER WEIGHT PRELOAD MEASUREMENT
Up to 180LBS 1/8″
180-240LBS 1/4″
240-300LBS 3/8″
300+LBS 1/2″
RIDER WEIGHT PRELOAD MEASUREMENT
Up to 180LBS 0″
180-240LBS 1/8″
240-300LBS 3/16″
300+LBS 1/4″
STEP FIVE: INSTALL LEGEND CARTRIDGES
A. Make sure the oil lock piece aligns with the stanchion (use a flashlight to ensure you can see all the way through the fork to the lower bolt hole).
IMPORTANT: VERIFY THAT THE STOCK REBOUND SPRINGS ARE REMOVED.
B. Install the provided rebound springs into the top of each stanchion. FIGURE E
C. With the slider and stanchion fully compressed, install the cartridge, making sure it is seated in the oil lock piece.
D. Clean and inspect the copper sealing washer and the threads of the
lower Allen bolt that were removed in Step 2. Make sure there are no
blemishes that would prevent the washer from sealing.
E. Install the lower Allen bolt and the copper sealing washer.
F. Hold the cartridge and tighten the lower Allen bolt to 15 ft. lbs. for a
41mm fork or 30 ft. lbs. for a 49mm fork.
STEP SIX: ADDING OIL AND BLEEDING
IMPORTANT: The type and amount of oil added ensures that the hydraulic bump stop functions properly.
A. Refer to the oil volume chart below for the type and amount of oil to add per fork.
B. Pour oil in the top of the stanchion, you will need to slowly pump the stanchion and slider a few times while doing this to distribute the oil. FIGURE F
C. Once the recommended amount of oil has been installed, slowly pump the stanchion and the slider up and down 10 to 12 times to bleed the air from the oil. FIGURE G
D. After bleeding the air from the oil, slide the stanchion up and thread it
onto the fork cap.
E. Tighten the fork cap to 25 ft. lbs.
OIL VOLUME CHART
NOTE: LEGEND SUSPENSIONS RECOMMENDS THE USE OF THE FOLLOWING FORK OILS: SCREAMIN’ EAGLE HEAVY, MAXIMA 20W V-TWIN, OR AN EQUIVALENT 20W FORK OIL
Part number Tube Size Ounces of Oil per Leg
0414-0747 49MM 11 OZ
Part number Tube Size Ounces of Oil per Leg
0414-0746 49MM 11 OZ
Part number Tube Size Ounces of Oil per Leg
0414-0748 41MM 3.5 OZ
STEP SEVEN: INSTALL FORKS
A. Once forks are completely assembled, re-install them onto your motorcycle. Follow the manufacturers’ torque specs for safety.
WARRANTY
All Legend ® Suspensions’ parts are guaranteed to the original purchaser to be free of manufacturing defects and workmanship. Parts that fail to conform to these conditions will be repaired or replaced at Legend ® Suspensions’ option if the parts are returned to Legend ® Suspensions by the original purchaser. Delivery of the original purchase invoice or receipt along with the part to Legend ® Suspensions is a condition precedent to Warranty coverage. Warranty coverage is limited lifetime.
In the event the original purchaser believes warranty service is required, the original purchaser must call or e-mail Legend ® Suspensions immediately to discuss the concern. Some concerns may be rectified by a telephone call and need no further course of action.
A part that is suspect of being defective must not be replaced by a Dealer or any other person without prior written authorization from Legend ® Suspensions. If it is deemed necessary for Legend ® Suspensions to make an evaluation of the part to determine whether a defect exists, a return authorization number (RA#) must be obtained from Legend ® Suspensions by the original purchaser. Properly obtaining a return authorization number from Legend ® Suspensions is a condition precedent to Warranty coverage.
The part must be packaged properly so as to not cause further damage and be returned prepaid to Legend ® Suspensions with a copy of the original invoice or receipt of purchase. If after evaluation, Legend ® Suspensions finds the part to be defective, Legend ® Suspensions will repair or replace the part, at the discretion and option of Legend ® Suspensions.
Exclusions
This warranty is void if:
(1) the Legend ® Suspensions’ part is repaired, modified or altered, unless such repair, modification or alternation is expressly authorized by Legend ® Suspensions in writing;
(2) the Legend ® Suspensions’ part becomes defective in whole or in part as a result of improper installation, improper maintenance, improper use, abnormal operation, or any other misuse or mistreatment of the Legend ® Suspensions’ part;
(3) the Legend ® Suspensions’ part is installed or used in any motorcycle or other vehicle other than an Unmodified Factory OEM Motorcycle;
(4) the Legend ® Suspensions’ part is installed or used on any motorcycle or other vehicle being used in any form of competitive riding or racing, off road riding, or stunt riding. Stunt riding shall include, but not be limited to, any form of acrobatic maneuvering of the motorcycle, wheelies, stoppies, burnouts, jumping, or operating the motorcycle at an excessive rate of speed;
(5) the Legend ® Suspensions’ part is installed or used on any motorcycle or other vehicle being operated at a speed in excess of the speed allowed by any applicable law, regulation, or ordinance or is operated in any other manner in violation of any applicable law, regulation or ordinance;
(6) the serial or parts identification number of the Legend ® Suspensions’ part is defaced or missing;
(7) the Legend ® Suspensions’ part is returned with no authorization number issued from Legend ® Suspensions; or
(8) the original purchase invoice or receipt is not provided to Legend ® Suspensions along with the part.
Additional Limitations
(1) Legend ® Suspensions shall have no warranty or liability obligation to cover work shop labor charges incurred to install or remove suspension systems or individual components.
(2) Electrical components are limited to a two-year manufacture’s warranty from the original invoice date or installation.
(3) Limited lifetime warranty as used within this warranty is further defined as the lifetime of the specific product line. Any product line that has been discontinued for which replacement parts are no longer available by is not covered by this warranty.
(4) The customer is liable for shipping charges to and from Legend ® Suspensions for warranty repairs or replacement parts consistent with this warranty. LEGEND ® SUSPENSIONS (INCLUDING ITS SUBSIDIARIES, AFFILIATES, OFFICERS, DIRECTORS, EMPLOYEES, AGENTS OR SHAREHOLDERS) SHALL NOT, UNDER ANY CIRCUMSTANCES, WHETHER AS A RESULT OF BREACH OF CONTRACT, BREACH OF WARRANTY, TORT, STRICT LIABILITY, THE FAILURE TO DELIVER, DELAY IN DELIVERY IN NONCONFORMING CONDITION, OR FOR ANY OTHER BREACH OF CONTRACT OR DUTY BETWEEN LEGEND ® SUSPENSIONS AND A CUSTOMER OR OTHERWISE, BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY OR PUNITIVE DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS OR REVENUES, LOSS OF OTHER GOODS OR ASSOCIATED EQUIPMENT OR DAMAGES TO ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL OR LABOR, COST OF REPLACEMENT OR SUBSTITUTE PRODUCTS, OR LOSS OF TIME. IN THE EVENT THAT LEGEND ® SUSPENSIONS SHALL BE UNABLE TO REPAIR OR REPLACE THE PRODUCT AS REQUIRED HEREIN, THE LIABILITY OF LEGEND ® SUSPENSIONS TO YOU OR ANY OTHER PARTY SHALL NOT EXCEED THE PRICE ACTUALLY PAID BY YOU FOR THE PRODUCT, UPON THE PAYMENT OF WHICH, LEGEND ® SUSPENSIONS SHALL BE RELEASED FROM AND DISCHARGED OF ALL FURTHER OBLIGATIONS AND LIABILITY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
WARNING: Legend ® Suspensions recommends this system be installed by a professional technician with professional knowledge of disassembly / reassembly procedures and post installation checks. Legend ® Suspensions are designed to be installed and used on Unmodified OEM Motorcycles only. Legend ® Suspensions assumes no responsibility for damage or injuries which may result from the use or installation of its products, whether or not properly installed or used. Installing a Legend ® Suspension may decrease initial ground clearance when in lowered position. The motorcycle will be lower to the ground and care should be taken to avoid bottoming out, especially over bumps or in turns. To maintain proper balanced geometry, we recommend riding in the stock height position.
Dispute Resolution
You agree that any dispute between you and Legend ® Suspensions arising hereunder will be resolved exclusively and finally by arbitration administered by the American Arbitration Association (“AAA”) and conducted under its rules, except as otherwise provided below.
The arbitration will be conducted before a single arbitrator and will be limited solely to the dispute between you and Legend ® Suspensions. The arbitration shall be held at any reasonable location in Meade County, South Dakota, or by submission of documents, by telephone, online or in person. Any decision rendered in such arbitration proceedings will be final and binding on each of the parties, and judgment may be entered thereon in any court of competent jurisdiction. Should either party bring a dispute in a forum other than AAA, the arbitrator may award the other party its reasonable costs and expenses, including attorney fees and disbursements incurred in staying or dismissing such other proceedings or in otherwise enforcing compliance with this dispute resolution provision.
YOU UNDERSTAND THAT YOU WOULD HAVE HAD A RIGHT TO LITIGATE DISPUTES THROUGH A COURT, AND THAT YOU HAVE EXPRESSLY AND KNOWINGLY WAIVED THAT RIGHT AND AGREED TO RESOLVE ANY DISPUTES THROUGH BINDING ARBITRATION.
For the purposes of this section, the term “dispute” means any dispute, controversy, or claim arising out of or relating to: (1) this Agreement, its interpretation, or the breach, termination, applicability or validity thereof, or (2) the purchase or use of any Product, Accessory, service or otherwise from Legend ® Suspensions.
For purposes of this Agreement, the term Legend ® Suspensions means Legend ® Suspensions, its subsidiaries, affiliates, directors, officers, employees, beneficiaries, agents or assigns; the term “you” means you, the original purchaser, your agents, beneficiaries, or heirs.
Governing Law
Both you and Legend ® Suspensions consent to the application of the laws of the State of South Dakota to govern, interpret, and enforce all of your rights and Legend ® Suspensions’ rights, duties, and obligations arising from, or relating in any manner to, the subject matter of this Limited Lifetime Warranty, without regard to conflict of law principles.